manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

NAVIGATOR: PARAMETERS

Front Cylinder Intake Pressure

example value: 1003 mbar

Pressure read by the front sensor.

Rear Cylinder Intake Pressure

example value: 1004 mbar

Pressure read by the rear sensor.

Front Cylinder estimated Intake Pressure

example value: 1003 mbar

Pressure estimated by the control unit according to the throttle position.

Rear Cylinder estimated Intake Pressure

example value: 1004 mbar

Pressure estimated by the control unit according to the throttle position.

NAVIGATOR: ELECTRICAL ERRORS

Front cylinder air pressure sensor P0105

 - short circuit to positive / open circuit, short circuit to

negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 34 of the VEHICLE con-

nector.

•

If the circuit is open, shorted to negative: voltage equal to zero has been detected at PIN 34

of the VEHICLE connector.

Troubleshooting

•

If short circuit to positive, see that the parameter of the front Cylinder Intake Pressure on

the diagnosis instrument reads approx. 1200 mbar; disconnect the large connector from the

filter box: if the value does not vary, it means that the cable is shorted between the filter box

connector and the control unit connector; restore the cable harness. If the value varies,

reconnect the filter box connector and disconnect the sensor connector: if the value does

not vary, it means that the cable is shorted between the filter box connector and the sensor

connector; restore the cable harness. Replace the sensor if the value varies.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 129

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

GAS GAS TXTPRO - 2009 Manual preview
TXTPRO - 2009
Brand: GAS GAS Pages: 57
Memphis Shades 2320-0024 Mounting Instructions preview
2320-0024
Brand: Memphis Shades Pages: 2
Shark OpenLine User Manual preview
OpenLine
Brand: Shark Pages: 52
R&G CP0482 Fitting Instructions Manual preview
CP0482
Brand: R&G Pages: 18
Crivit 271528 Instructions For Use Manual preview
271528
Brand: Crivit Pages: 30
Denali LAH.07.10401 Instruction Manual preview
LAH.07.10401
Brand: Denali Pages: 2
X-lite X-801 Operating Instructions Manual preview
X-801
Brand: X-lite Pages: 33
DELTA-SPORT crivit sports 101545 Instructions For Use Manual preview
crivit sports 101545
Brand: DELTA-SPORT Pages: 42
Sealey VS779.V3 Instructions preview
VS779.V3
Brand: Sealey Pages: 2
Power Fist 8879785 Manual preview
8879785
Brand: Power Fist Pages: 12
Oxford Drystash Series Manuallines preview
Drystash Series
Brand: Oxford Pages: 20
Oxford Heritage Series Manualline preview
Heritage Series
Brand: Oxford Pages: 28
APRILIA DORSODURO 1200 ABS - ATC Service Station Manual preview
DORSODURO 1200 ABS - ATC
Brand: APRILIA Pages: 408
6KU FIXIE Step By Step Building Manual preview
FIXIE
Brand: 6KU Pages: 17
ORTILEB SSF 16Z Technical Documentation Manual preview
SSF 16Z
Brand: ORTILEB Pages: 20
KTM 450 EXC RACING 2006 Owner'S Manual preview
450 EXC RACING 2006
Brand: KTM Pages: 111
KTM 390 DUKE 2017 Owner'S Manual preview
390 DUKE 2017
Brand: KTM Pages: 255
Ear Defender TuneUp H34-M28-L19 User Instruction preview
TuneUp H34-M28-L19
Brand: Ear Defender Pages: 64

Brands by name

Popular brands

Load more brands