APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 198 / 379

Disassembling the clutch

LUTCH

pos.

Description

Type

Quantity

Torque

Notes

Clutch spring fastener screw

12 Nm (8.85 lbf ft)

•

Remove the clutch side housing.

•

Unscrew and remove the six screws by

loosening them 1/4 of a turn at a time;

operate in stages and diagonally, and

retrieve the washers and the clutch

springs.

•

Remove the thrust plate.

Engine

DORSODURO FACTORY ABS

ENG - 198

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands