APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 54 / 379

There are three crankshaft classes selectable for

each bearing:

•

4 - 5 - 6 for the flywheel side;

•

7 - 8 - 9 for the clutch side;

The class is stamped on the outer face of the

crankshaft counterweight.

NOTE

TWO DIFFERENT CRANKSHAFT CLASSES MAY BE POS-
SIBLE ON THE TWO BEARINGS.

RANKSHAFT

CLASSES

Specification

Desc./Quantity

Crankshaft classes 4 - 7

Main journals - diameter: 49.978 - 49.984 mm (1.9676 - 1.9679

in)

Crankshaft classes 5 - 8

Main journals - diameter: 49.972 - 49.978 mm (1.9674 - 1.9676

in)

Crankshaft classes 6 - 9

Main journals - diameter: 49.990 - 49.984 mm (1.9681 - 1.9679

in)

Once the categories below are checked:

•

crankcase

•

flywheel side main journal

•

clutch side main journal

choose the bushings used for assembly from the following table

See also

Removing the flywheel cover

MAIN BUSHINGS

Main journal

Crankcase class 1

Crankcase class 2

Class 4 main journal (l.v.)

Semi-bushing type A (red)

Semi-bushing type B (blue)

Class 5 main journal (l.v.)

Semi-bushing type B (blue)

Semi-bushing type C (yellow)

Class 6 main journal (l.v.)

Semi-bushing type E (green)

Semi-bushing type A (red)

Class 7 main journal (l.f.)

Semi-bushing type A (red)

Semi-bushing type B (blue)

Class 8 main journal (l.f.)

Semi-bushing type B (blue)

Semi-bushing type C (yellow)

Class 9 main journal (l.f.)

Semi-bushing type E (green)

Semi-bushing type A (red)

Crankcase class (internal marking on first gen-

eration crankcases)

Two different crankcase classes (A or B) are avail-

able, selected in relation to the centre-to-centre

distance between the primary reduction gears.

The class is indicated on the clutch side crankcase

half near the front cylinder area.

NOTE

IN THE EVENT OF CRANKCASE REPLACEMENT, THE PRI-
MARY REDUCTION GEAR IS SUPPLIED READY MESHED.

Characteristics

DORSODURO FACTORY ABS

CHAR - 54

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands