manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

•

Remove the saddle.

•

Undo and remove the two upper

screws and collect the washers.

•

Remove the exhaust end backwards

by sliding off the two brackets from the

rubber rings in the upper section and

the bracket from the chassis retainer in

the lower part.

Removing the manifold - tail pipe

•

Remove the front exhaust manifold.

•

Disconnect the lambda probe.

•

Loosen the exhaust manifold and the

exhaust end clamps from the rear cyl-

inder.

•

Remove the manifold - terminal coupling.

See also

Removing the

Chassis

DORSODURO FACTORY ABS

CHAS - 308

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Sachs Bikes MadAss 50 Owner'S Manual preview
MadAss 50
Brand: Sachs Bikes Pages: 83
AJP PR4 Service Manual preview
PR4
Brand: AJP Pages: 191
Yamaha Tmax XP500Z Owner'S Manual preview
Tmax XP500Z
Brand: Yamaha Pages: 102
Yamaha TT-R110E 2017 Owner'S Manual preview
TT-R110E 2017
Brand: Yamaha Pages: 88
Yamaha YZ85G Owner'S Manual preview
YZ85G
Brand: Yamaha Pages: 88
Avenger 160 STREET Manual preview
160 STREET
Brand: Avenger Pages: 31
Memphis Shades MEM5806 Quick Start Manual preview
MEM5806
Brand: Memphis Shades Pages: 2
AKE PowerCom INNOVA Plus Business Quick Start Manual preview
PowerCom INNOVA Plus Business
Brand: AKE Pages: 2
Touratech 01-040-2017-0 Instruction preview
01-040-2017-0
Brand: Touratech Pages: 4
Sealey WC06 Instructions preview
WC06
Brand: Sealey Pages: 2
Benelli TnT302S Owner'S Manual preview
TnT302S
Brand: Benelli Pages: 55
Benelli TNT25 Owner'S Manual preview
TNT25
Brand: Benelli Pages: 65
Benelli BN125 2018 Owner'S Manual preview
BN125 2018
Brand: Benelli Pages: 75
RSI HA1002 Installation Instructions preview
HA1002
Brand: RSI Pages: 2
KED PECTOR Manual preview
PECTOR
Brand: KED Pages: 16
KTM Power Parts Information preview
Power Parts
Brand: KTM Pages: 3
Indian Motorcycle Ride Command Quick Start Manual preview
Ride Command
Brand: Indian Motorcycle Pages: 2
KTM 250 EXC-F EU 2010 Owner'S Manual preview
250 EXC-F EU 2010
Brand: KTM Pages: 136

Brands by name

Popular brands

Load more brands