manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 193

•

Screw the anticlockwise bolt of the

special tool on the external body.

•

Keeping the external body blocked and

gripping the key, screw the anticlock-

wise bolt so as to remove the flywheel

from the crankshaft.

Specific tooling

020713Y

 

Flywheel extractor

•

Unscrew and remove the anticlockwise bolt of the special tool from the external body.

•

Undo the screw from the crankshaft.

Specific tooling

020713Y

 

Flywheel extractor

•

Remove the flywheel together with the

freewheel.

•

Remove the start-up transmission

gear.

•

In case of malfunction, the start-up

transmission gear cannot be over-

hauled. Therefore, the complete trans-

mission gear should be replaced.

•

Collect the crankshaft woodruff key.

DORSODURO FACTORY ABS

Engine

ENG - 193

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands