APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 266 / 379

1. Ride by Wire system control (throttle map)

2. Injection/ignition control

3. System safety checks

1 - Ride by Wire system control

THROTTLE GRIP POSITION SENSOR

The throttle grip is the part to which the throttle control cables

arrive; its task is to translate the rider's power request into an electrical signal to be sent to the electronic

control unit. The two throttle cables (opening and closing) actuate on a scroll mounted on a shaft and

which is sent back to its home position by a return spring.

On the shaft covers there are 2 double track potentiometers (4 control tracks) by means of which the

torque demand is read (and checked).

Marelli 5DM electronic control unit

Besides the regular control functions of the injection system, it

supervises the throttle bodies: Through the throttle grip position sensor, it reads the torque demand

and, through the THROTTLE MAP, it decides the throttle opening and sends the command to the throttle

valve control unit. It checks the correct operation of each component (Self-diagnosis), of the system

(Safety), and carries out the emergency procedure (Recovery).

EFI throttle control unit

The control unit receives the target throttle opening to be carried out and it

actuates on the control acting on the throttle body motors.

It checks (through the throttle position sensor signal) that the throttle bodies have reached the target

position.

It communicates the position reached to the Marelli control unit. It does not actuate on Safety strategies.

Throttle Body

The two throttle bodies are made up of:

•

Throttle valve with 2 return springs for the controlled minimum opening position.

•

DC electrical motor

•

Tinned double throttle position sensors with magnetic control (contactless)

The throttle bodies do not require any maintenance and cannot be overhauled. In case of electric or

mechanic malfunction, replace the whole unit.

Pressure sensors

The pressure sensors (one per cylinder) are fundamental not only for the injection

map at low and stabilised speeds but also for checking the Ride by Wire system: their signal is connected

to a TORQUE CHAIN for checking the correct opening of the throttle valves.

Intake air temperature sensor

The signal coming from the sensor is used to calculate the estimated

torque since the oxygen in the air also depends on its density which varies according to temperature.

2 - Injection/ignition control

Map for injection type (alpha-D)/rpm where:

•

alpha is the throttle position

•

D is the pressure measured at inlet ducts

•

Rpm are the engine revolutions

•

At idle and for slow and stabilised speeds D/n

Power supply

DORSODURO FACTORY ABS

P SUPP - 266

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands