manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

Target idle rpm

NAVIGATOR: ELECTRICAL ERRORS

EEPROM Error P0601

 - circuit not operational.

Error cause

•

Replace injection ECU. The instrument panel does not indicate the presence of this error

even in the ATT status.

RAM Error P0604 -

 circuit not operational.

Error cause

•

Replace injection ECU. The instrument panel does not indicate the presence of this error

even in the ATT status.

ROM Error P0605 -

 circuit not operational.

Error cause

•

Replace injection ECU. The instrument panel does not indicate the presence of this error

even in the ATT status.

A/D converter P0607-

 circuit not operational.

Error cause

•

Replace injection ECU.

Level 2 safety reset P0608

Error cause

•

As the level 2 safety system (comparison between requested torque and calculated torque)

has detected a fault, the control unit has reset engine (C gravity).

Troubleshooting

•

Continue fault search for the other errors detected.

Safety Engine Stop P0609

Error cause

•

As the level 3 safety system (control EEPROM) has detected a fault, the control unit has

shut off the engine (D gravity).

Troubleshooting

•

Replace Marelli control unit.

Reset lines error P0610-

 circuit not operational

Error cause

•

Problems on the reset lines (PINS 55 and 56 of the VEHICLE connector) of the throttle

motors: lines used to interrupt motor functioning for safety reasons.

Troubleshooting

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 116

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

BMW Motorrad F 850 GS Adventure 2019 Rider'S Manual preview
F 850 GS Adventure 2019
Brand: BMW Motorrad Pages: 346
R&G FI0054BK Fitting Instructions preview
FI0054BK
Brand: R&G Pages: 4
Velmia Premium Motorcycle Cover Instructions For Use Manual preview
Premium Motorcycle Cover
Brand: Velmia Pages: 32
Ohlins YA 469 Mounting Instructions preview
YA 469
Brand: Ohlins Pages: 4
Caberg Droid Manual preview
Droid
Brand: Caberg Pages: 16
Yamaha GRIZZLY 90 2020 Owner'S Manual preview
GRIZZLY 90 2020
Brand: Yamaha Pages: 132
Yamaha RAPTOR 90 2020 Owner'S Manual preview
RAPTOR 90 2020
Brand: Yamaha Pages: 132
Yamaha YFM45FGZ Owner'S Manual preview
YFM45FGZ
Brand: Yamaha Pages: 166
Yamaha XVZ12L Service Manual preview
XVZ12L
Brand: Yamaha Pages: 452
Yamaha YFM09GYXM 2020 Owner'S Manual preview
YFM09GYXM 2020
Brand: Yamaha Pages: 132
hepco & becker 6303534 00 01 Quick Start Manual preview
6303534 00 01
Brand: hepco & becker Pages: 2
Malossi DARK SMOKE SPORT Fitting Instructions preview
DARK SMOKE SPORT
Brand: Malossi Pages: 4
Mash Black Seven 250 User Manual preview
Black Seven 250
Brand: Mash Pages: 62
Marzocchi Shiver 50 Manual preview
Shiver 50
Brand: Marzocchi Pages: 116
Cagiva 1994 MITO ev Workshop Manual preview
1994 MITO ev
Brand: Cagiva Pages: 124
LSK FuelGaugePro FGP-SENSOR Installation Manual preview
FuelGaugePro FGP-SENSOR
Brand: LSK Pages: 11
FMF SUZUKI RM80 Installation preview
SUZUKI RM80
Brand: FMF Pages: 4
Giro Helmet Owner'S Manual preview
Helmet
Brand: Giro Pages: 8

Brands by name

Popular brands

Load more brands