APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 119 / 379

Speed sensor

5D91 the signal works irregularly:

faulty sensor or signal interference.

Troubleshooting:

Check speed sensor retainer. If it is not OK, restore it. If it is OK, check if the tone

wheel is dirty, deformed or wrongly fixed. If any of this happens, replace the tone wheel. Otherwise,

replace the speed sensor.

5D92 the signal decreases periodically:

Possible tone wheel fault due to deformations or dirt; pos-

sible alterations on the wheel bearing surface. In very rare cases, abnormal tone wheel vibrations.

Troubleshooting:

Check if the tone wheel is dirty, deformed or wrongly fixed. If the tone wheel is not

OK, replace it. If it is OK, check for possible faults in the wheel bearings and if it is not OK, replace the

bearings.

5D93 missing signal or speed measured too low in relation to the rear wheel:

faulty sensor or

missing sensor/tone wheel. Or excessive distance between the sensor and the tone wheel or tone wheel

with wrong number of teeth.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, replace the speed sensor.

5D94 no acceleration after pressure reduction:

Faulty sensor or missing sensor/tone wheel or ex-

cessive distance between the sensor and the tone wheel.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, replace the speed sensor.

5D95 excessive speed measured:

Faulty sensor or tone wheel, or tone wheel with wrong number of

teeth or wrong tyre size.

Troubleshooting:

Check that the speed sensor and the tone wheel are installed. If they are not, install

them. If they are, check the speed sensor retainer. If it is not OK, restore it. If it is, check if the tone

wheel has the correct number of teeth or if it is dirty, deformed or wrongly fixed. If it is not OK, replace

the tone wheel and if it is OK, check that the tyre size is the correct one. If it is not OK, replace it. If it is

OK, check that the tyre pressure is the correct one. If it is not OK, restore it; if it is OK, replace the speed

sensor.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 119

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands