APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 265 / 379

Diagram

HROTTLE

BODY

pos.

Description

Type

Quantity

Torque

Notes

Intake union fastener screw

12 Nm (8.85 lbf ft)

Loctite 242

RBW control unit fastener screw

3.50 Nm (2.58 lbf ft)

Loctite 242

Injector fastener screw

12 Nm (8.85 lbf ft)

Loctite 242

Injection Throttle Body fastener

screw

12 Nm (8.85 lbf ft)

Loctite 242

Ride by Wire

RIDE BY WIRE

Operating logic

Those riding motorbikes do not require a specific throttle valve opening from their engines but actually

a specific torque. The Ride by Wire system has been so designed that the throttles of the throttle bodies

are mechanically isolated from the throttle control; their actuation depends exclusively on 2 electrical

motors controlled by the control unit. Therefore, there is a "Throttle map" to which the control unit refers

in order to decide the position at which the throttle valves should be and at what speed they should

reach the pre-set position. The main parameters which influence the throttle map are:

•

Throttle position and opening/closing speed

•

Engine rpm

•

Inlet pressure read at each inlet manifold

•

Rear and front throttle valve position

•

Air temperature

The functions required from the Marelli control unit therefore are:

DORSODURO FACTORY ABS

Power supply

P SUPP - 265

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands