APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 208 / 379

•

Separate the cylinder from the head.

•

Collect the gasket.

See also

Removing the

cylinder

Cylinder head

EAD

pos.

Description

Type

Quantity

Torque

Notes

Water Temperature Sensor

M12x1.5

23 Nm (16.96 lbf ft)

Threaded plug for water sensor seat

M12x1.5

10 Nm (7.38 lbf ft)

Loctite Drise AL 506

Head stud bolt fastener nut - pre-

tightening

M10x1.25

10 Nm (7.38 lbf ft)

Lubricate the

threads before tight-

ening

Head stud bolt fastener nut - tighten-

ing

M10x1.25

13 Nm (9.59 lbf ft) + 90°

+ 90°

Lubricate the

threads before tight-

ening

Fastener for Head / Cylinder / Outer

side crankcase

13 Nm (9.59 lbf ft)

Fastener for Head / Cylinder / Inner

side crankcase

12 Nm (8.85 lbf ft)

Nut fastening Stud Bolts / Head

12 Nm (8.85 lbf ft)

Engine

DORSODURO FACTORY ABS

ENG - 208

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands