APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 222 / 379

YLINDER

pos.

Description

Type

Quantity

Torque

Notes

Chain tensioner fastener screw

13 Nm (9.59 lbf ft)

Cylinder plate fastener screw

13 Nm (9.59 lbf ft)

Chain tensioner adjustment screw

5.50 Nm (4.06 lbf ft)

Removing the cylinder

•

Remove the timing chain.

•

Undo and remove the two head fas-

tener screws located in the timing

chain compartment.

•

Undo and remove the outer screw.

•

Undo and remove the four nuts, pro-

ceeding in stages and in a diagonal

pattern.

•

Ease the cylinder head assembly off

the stud bolts.

•

Remove the three nuts fastening the

cylinder head on the intake and ex-

haust sides.

Engine

DORSODURO FACTORY ABS

ENG - 222

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands