APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 284 / 379

•

Fit the sleeve on the stem and set the

oil seal into position with the aid of the

specific tool.

Specific tooling

AP8140189

Oil seal fitting tool for Ø 43 mm

(1.69 in) orifices

AP8140146

Weight

•

Insert the retainer ring in its position.

•

Fit the dust gaiter with the specific tool.

Specific tooling

AP8140189

Oil seal fitting tool for Ø 43 mm

(1.69 in) orifices

AP8140146

Weight

•

Insert the pumping member pin in the

stem.

Suspensions

DORSODURO FACTORY ABS

SUSP - 284

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands