manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

MOVING THEM (BLUE STAMP + BLUE BAND). THE CONNECTOR AND THE BLUE BAND
SHOULD BE PLACED TO THE LEFT. THE CONNECTOR AND THE WHITE BAND SHOULD BE
PLACED TO THE RIGHT.

NOTES

 The two connectors which get to the throttle grip sensor are the same but they should NEVER

be inverted. Mark or check the connector marking before removing them (blue stamp+blue band).

Removal

•

When required, disconnect the corre-

sponding connectors, undo and re-

move the two screws and remove the

throttle grip position sensor.

Intake pressure sensor

INTAKE AIR PRESSURE SENSOR

Function

The pressure sensors (one per cylinder) are fundamental not only for the injection configuration at low

and stabilised speeds, but also for checking the Ride by wire system: their signal is connected to a

TORQUE CHAIN for checking the correct opening of the throttle valves.

Operation / Operating principle

Diaphragm sensor which translates the diaphragm position into electrical voltage when in contact with

the intake air.

Level in electrical circuit diagram:

intake air pressure sensor

Location:

•

on the vehicle: inside the filter box

•

connector: on the sensor

Pin-out:

1. Fuel system

2. Ground connection

3. Output signal

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 128

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

probrake SU10-5 Mounting Instruction preview
SU10-5
Brand: probrake Pages: 2
Dowco Rally Pack Value Series Installation Instructions preview
Rally Pack Value Series
Brand: Dowco Pages: 3
Ohlins HO 1072 Mounting Instructions preview
HO 1072
Brand: Ohlins Pages: 2
Lambretta V125 Special 2018 User Manual preview
V125 Special 2018
Brand: Lambretta Pages: 53
KTM F8103S4 Setup Instructions preview
F8103S4
Brand: KTM Pages: 36
Kenwood KCA-HX7C Instruction Manual preview
KCA-HX7C
Brand: Kenwood Pages: 36
Kenwood KCA-HX5M Instruction Manual preview
KCA-HX5M
Brand: Kenwood Pages: 97
Saddlemen FTB Series Installation Instruction preview
FTB Series
Brand: Saddlemen Pages: 6
Scott 2 Operation And Maintenance Instructions preview
2
Brand: Scott Pages: 22
SCORPION RKT-89 Fitting Instructions preview
RKT-89
Brand: SCORPION Pages: 2
SCORPION SIGS39 Installation Manual preview
SIGS39
Brand: SCORPION Pages: 15
KTM 60 65 SX Manual preview
60 65 SX
Brand: KTM Pages: 20
Shad X0SE04P Manual preview
X0SE04P
Brand: Shad Pages: 2
Shad SYM JOYMAX 125 GTS '13 Quick Start Manual preview
SYM JOYMAX 125 GTS '13
Brand: Shad Pages: 2
Shad TOPMASTER Y0RX53ST Quick Start Manual preview
TOPMASTER Y0RX53ST
Brand: Shad Pages: 2
Shad SH26 Owner'S Manual preview
SH26
Brand: Shad Pages: 3
Shad SH40 User Manual preview
SH40
Brand: Shad Pages: 3
Shad S0GS61SF Manual preview
S0GS61SF
Brand: Shad Pages: 3

Brands by name

Popular brands

Load more brands