APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 73 / 379

background image

The electrode gap should be between 0.6 ÷ 0.7

mm (0.023 ÷ 0.027 in). Otherwise, replace the

spark plug.

•

Make sure the washer is in good con-

ditions.

Installation:

•

Once the washer is fitted, screw the

spark plug carefully to avoid damaging

the thread.

•

Tighten it using the spanner supplied in

the toolkit, make each spark plug com-

plete 1/2 a turn to press the washer.

CAUTION

TIGHTEN THE SPARK PLUG CORRECTLY, OTHERWISE
THE ENGINE MAY OVERHEAT AND GET IRRETRIEVABLE
DAMAGED. USE ONLY THE RECOMMENDED TYPE OF
SPARK PLUG, OTHERWISE, THE ENGINE DURATION AND
PERFORMANCE COULD BE COMPROMISED.

Locking torques (N*m)

Spark plug

13 Nm (9.59 lbf ft)

Engine oil

Check

Check the engine oil level frequently.

NOTE

CARRY OUT MAINTENANCE OPERATIONS AT HALF THE INTERVALS SPECIFIED IF THE VE-
HICLE IS USED IN PARTICULAR RAINY OR DUSTY CONDITIONS, OFF ROAD OR FOR TRACK
USE.

ENGINE OIL LEVEL MUST BE CHECKED WHEN THE ENGINE IS WARM.
IF YOU CHECK LEVEL WHEN THE ENGINE IS COLD, OIL LEVEL COULD TEMPORARILY DROP
BELOW THE "MIN" MARK.
THIS SHOULD NOT BE CONSIDERED A PROBLEM PROVIDED THAT THE ALARM WARNING
LIGHT AND THE ENGINE OIL PRESSURE ICON DO NOT TURN ON SIMULTANEOUSLY ON THE
DISPLAY.

CAUTION

DO NOT IDLE THE ENGINE WITH THE VEHICLE AT A STANDSTILL TO WARM THE ENGINE AND
BRING THE OIL TO OPERATING TEMPERATURE.
PREFERABLY CHECK THE OIL AFTER A JOURNEY OF AFTER TRAVELLING APPROXIMATELY
15 Km (10 miles) IN EXTRAURBAN CONDITIONS (ENOUGH TO WARM UP THE ENGINE OIL TO
OPERATING TEMPERATURE).

DORSODURO FACTORY ABS

Maintenance

MAIN - 73

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
71
72
73
74
75
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: LAZER Pages: 6

HIGHSIDER VICTORY

Brand: Paaschburg & Wunderlich Pages: 5

990D0-44G00-ALM

Brand: Suzuki Pages: 24

MILWAUKEE-EIGHT 5833

Brand: JIMS Pages: 10

Brand: Can-Am Pages: 196

Brand: Free Spirits Pages: 28

Brand: Yamaha Pages: 94

Star XVS13CG 2015

Brand: Yamaha Pages: 98

Star XV250G 2015

Brand: Yamaha Pages: 88

Star XVS13CTD 2012

Brand: Yamaha Pages: 104

Brand: Yamaha Pages: 104

Star XV250H 2016

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 98

Brand: Triumph Pages: 126

Brand: Leatt Pages: 26

Brand: Leatt Pages: 26

Brand: Wunderkind Custom Pages: 4

Brand: Bagster Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands