APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 126

Page: 126 / 379

Right side Throttle Grip Position sensor - track C P0152-

short circuit to positive / open circuit, short

circuit to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 30 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 30 of the ENGINE connector.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the right Throttle Grip position

Sensor - track C: disconnect the right connector and see the value displayed by Navigator:

if the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle

grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the key set to ON, check that there

is power supply for the potentiometer PIN A and that PIN C is connected to ground. If both

are correct, replace the throttle grip sensor; if not, check the continuity of the cable that is

not functioning properly: if there is continuity, replace the control unit; if not, restore the wiring

Right side Throttle Grip Position sensor - track D P0153

- short circuit to positive / open circuit, short

circuit to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 44 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 44 of the ENGINE connector.

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the right Throttle Grip Position

Sensor - track D: disconnect the right connector and see the value displayed by Navigator:

if the voltage does not vary, there is a short circuit in the cable wiring; replace the throttle

grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the switch key set to ON, check

that there is power supply for the potentiometer PIN D and that PIN F is connected to ground.

If both are correct, replace the throttle grip sensor; if not, check the continuity of the cable

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 126

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Brands by name

Popular brands