APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 212 / 379

background image

•

a: 35.13 / 35.17 mm (1.3831 / 1.3846

in); Limit: 35.00 mm (1.3779 in);

•

b: 28 mm (1.1023 in);

•

Fasten the camshaft in horizontal po-

sition, as shown in the figure, and make

it spin to check the eccentricity with a

dial gauge; if necessary, replace the

component.

Camshaft eccentricity maximum limit 0.040

mm (0.0016 in)

Valve check

CAUTION

REPLACE THE VALVES ONE AT A TIME. DO NOT MIX THE COMPONENTS. EACH VALVE MUST
BE INSERTED INTO ITS SEAT, WHICH IS MARKED PRIOR TO REMOVAL.

CAUTION

THE SEAT (1) ON THE VALVE HEAD CANNOT BE REGROUND. IF REQUIRED, REPLACE THE
VALVE.
GRINDING WITH ABRASIVE PASTE IS ALLOWED; VALVE STEM END REGRINDING IS NOT AL-
LOWED.

Clean off any combustion residues from the

valves.

Check the seat (1) on the valve head with a ruler

flush.

The surface of the seat must not be concave; re-

place the valve if necessary.

Check the clearance between the stem and the

valve guide:

inlet:

0.013 - 0.040 mm (0.00051 - 0.00157 in);

limit: 0.080 mm (0.00315 in)

outlet:

0.025 - 0.052 mm (0.00098 - 0.00205 in);

limit: 0.100 mm (0.00394 in)

Engine

DORSODURO FACTORY ABS

ENG - 212

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
210
211
212
213
214
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: B-PWR Pages: 13

Brand: R&G Pages: 21

Brand: MRA Pages: 9

Brand: Honda Pages: 28

Brand: R&G Pages: 6

Brand: RDMOTO Pages: 2

Brand: YCF Pages: 78

Brand: KTM Pages: 36

Brand: X-lite Pages: 33

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 3

Brand: DYNATEK Pages: 11

crivit sports 101545

Brand: DELTA-SPORT Pages: 42

Brand: Kobalt Pages: 27

Krauser 610.092 00 02

Brand: Wunderlich Pages: 4

Brand: BUMOT Pages: 5

Brand: RIEJU Pages: 116

Brand: Benelli Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands