APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 179 / 379

•

Working on the left side, unscrew and

remove the lower bolt.

•

Working on the right side, slightly slide

off the lower bolt.

•

Collect the spacer on the opposite

side.

•

Remove the lower pin and collect the

washer.

•

Lower the engine.

See also

Vehicle preparation

Installing the engine to the vehicle

•

Place the engine on a suitable lower stand.

•

Lift the engine.

•

Place the engine so that the rear attachments on the chassis are aligned.

•

Working on the right side, insert the

three bolts with their washers.

•

Working on the right side, place the

spacers on the three bolts between the

engine block and the chassis.

CAUTION

THE SPACERS HAVE DIFFERENT SIZES. REFIT THEM IN
THE SAME WAY THEY WERE BEFORE BEING REMOVED.

DORSODURO FACTORY ABS

Engine from vehicle

ENG VE - 179

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands