manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 162

RUN/STOP switch

Run / stop switch

Function

It tells the control unit if the driver wishes to enable

engine start-up or to keep the engine running.

Operation / Operating principle

If the driver wants to shut off the engine or to dis-

able engine start-up, the switch should be open,

i.e. the Marelli control unit should not detect volt-

age at VEHICLE connector PIN 26.

Level in electrical circuit diagram:

Start-up ena-

bling switches.

Location:

•

on the vehicle: right light switch

•

connector: fixed to the "L" support

bracket placed over the clutch housing.

Electrical characteristics:

•

STOP position: the circuit is open

•

RUN position: closed circuit (continui-

ty)

Pin-out:

1. Yellow/grey cable: -

2. Red/black cable: Voltage 12V

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: PARAMETERS

-

NAVIGATOR: STATUSES

Run / stop switch

Example value

:Run/Stop

Indication on Navigator always STOP: disconnect the connector and, with the switch set to RUN, check

if there is continuity toward the switch of the two yellow/grey and red/black cables: if there is no con-

tinuity, replace the sensor; if there is, check the connector. If not OK, restore the cable harness; if it is

OK, with key set to ON, check if there is voltage to the red/black cable: if there is no voltage, restore

the cable harness; if there is, check the yellow/grey cable ground insulation: if there is continuity to

ground, restore the cable harness; if it is correct, take the key to OFF and check the VEHICLE connector

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 162

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands