manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 318

Riding with an active ABS system

•

At engine start-up, the ABS warning

light (5) on the instrument panel (4)

turns on and remains on until the vehi-

cle exceeds 5 km/h (3.1 mph).

If the ABS warning light remains on when the

vehicle is running, it means that a fault has

been detected and the ABS system has been

automatically deactivated.

20 A fuse (ABS Main fuse) (6)

Protects: ABS Control unit.

Guide to diagnosis

PREMISE

Each time the key is ON, at least one current or stored* error of the ABS system is often detected:

•

the EFI warning light turns on permanently and the word ABS is shown on the display (NA

850 Mana ABS).

•

the ABS warning light turns on permanently (SL 750 SHIVER ABS / DORSODURO 750

ABS).

If on the vehicle NA 850 Mana ABS, temporary errors of other control units are detected, the word ABS

shown on the display is displayed instead of the word relative to the other control units where errors

have been detected (e.g. GEAR or SERVICE).

The ABS system is deactivated!

The system operates perfectly just as any other braking system without ABS

* The diagnosis requires exceeding the 5 km/h.

Each time the key is ON, if at least one current or stored* error of the ABS system is not detected:

•

the EFI warning light flashes and the word ABS is shown on the display (NA 850 Mana ABS).

•

the ABS warning light flashes (SL 750 Shiver ABS / Dorsoduro 750 ABS)

When the 5 km/h (3.11 mph) are exceeded:

- if errors are not detected

Braking system

DORSODURO FACTORY ABS

BRAK SYS - 318

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands