APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 142 / 379

connector and check if there is voltage at PIN -: if there is voltage, restore the filter box cable

harness. If there is no voltage, replace the sensor.

•

shorted to negative: disconnect the injector connector, set the key to ON and check if there

is a ground connection on the grey/red cable: if there is voltage, restore the cable harness

between the filter box connector and the Marelli control unit; if there is no voltage, reconnect

the connector and disconnect the injector connector and check if there is a ground connec-

tion on PIN -: if there is voltage, restore the filter box cable harness. If there is no voltage,

replace the injector.

•

the circuit is open: check the component correct electrical characteristic: if it is not correct,

replace the component; if it is correct, check the filter box small connector, the connector on

the component and the Marelli control unit connector: If not OK, restore. If OK, check cable

continuity between the ENGINE PIN 34 and component PIN - and restore the cable harness.

Coil

COIL

Function

Spark generation.

Operation / Operating principle

Inductive discharge system.

Level in electrical circuit diagram:

coils and in-

jectors.

Location:

•

on the vehicle: on the cylinder head

•

connector (if available): -

Electrical characteristics:

•

Primary circuit resistance: approx. 1

Ohm at 20°C between PIN 1 and 3.

•

Secondary circuit resistance: MOhm

value range (with positive probe on

coil).

Pin-out:

1. batt V

2. Secondary circuit ground connection

3. Activation from control unit

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 142

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands