manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 306

LUBRICATE THE CHAIN ON A REGULAR BASIS, PARTICULARLY IF YOU DETECT DRY OR
RUSTY PARTS.
FLATTENED OR JAMMED CHAIN LINKS SHOULD BE LUBRICATED AND GOOD OPERATING
CONDITIONS RESTORED.

THE GEARING CHAIN HAS SEALING RINGS AMONG THE LINKS THAT KEEP THE GREASE
INSIDE.
ADJUST, LUBRICATE, WASH AND REPLACE THE CHAIN WITH UTMOST CAUTION.

CLEANING AND LUBRICATION

Do not wash the chain with water jets, steam jets, high-pressure water jets and highly flammable sol-

vents.

•

Wash the chain with fuel oil or kerosene. Maintenance operations should be more frequent

if there are signs of quick rust.

Lubricate the chain at the intervals specified on the routine maintenance table and whenever necessary.

•

Wash the chain, allow to dry and lubricate with spray grease for sealed chains.

Stand

S

TAND

 

ASSEMBLY

pos.

Description

Type

Quantity

Torque

Notes

1

Stand screw

M10x1.25

1

10 Nm (7.37 lbf ft)

Loctite 243

2

Thin nut

M10x1.25

1

30 Nm (22.13 lbf ft)

Loctite 243

3

Spring fixing pin

-

1

7.5 Nm (5.53 lbf ft)

-

4

TCEI screw fastening stand switch

M5x16

2

7 Nm (5.16 lbf ft)

-

Chassis

DORSODURO FACTORY ABS

CHAS - 306

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands