manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

The Aprilia Dorsoduro Factory ABS 2011 is a high-performance motorcycle built for thrilling rides. To ensure its optimal maintenance and care, download the free Service Station Manual from manualshive.com to access comprehensive instructions and guidelines. This manual is essential for any Dorsoduro owner seeking to maximize their riding experience.

Share
Download
background image

•

Remove the crankshaft.

See also

Splitting the

crankcase halves

Inspecting the crankcase halves

BEARINGS AND OIL SEAL CHECK

Thoroughly clean the two sections of the crankcase, the ball bearings, the threads of the crankcase

fixing screws and the bearing seats with a non-aggressive solvent. Clean the seal surfaces and check

that they are not damaged.

CAUTION

TO AVOID DAMAGING BOTH CRANKCASE HALVES PLACE THEM ON A FLAT SURFACE.

Check that both crankcase halves are not cracked or damaged.

Check that all threads are in proper conditions.

Check that all oil seals remaining in their position are not worn or damaged.

Check all ball bearings for clearance, smoothness and potential distortions.

CAUTION

LUBRICATE BALL BEARINGS WITH ENGINE OIL BEFORE FURTHER CHECKING.

If the internal ring does not rotate smoothly and silently or if there is some noise while it turns, it means

that the bearing is faulty and must be replaced.

OIL FILTER AND OIL DELIVERY PIPE CHECK

Check the oil filter for damage. If necessary, replace the part.

Clean the oil net with petrol and inspect the net links for potential damage.

CHECK THE ENGINE OIL FILTER O-RING.

Engine

DORSODURO FACTORY ABS

ENG - 244

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

hepco & becker 6616519 01 01 Quick Manual preview
6616519 01 01
Brand: hepco & becker Pages: 4
Abus GameChanger Instruction Manual preview
GameChanger
Brand: Abus Pages: 18
GAS GAS TXT BOY - 2006 User Manual preview
TXT BOY - 2006
Brand: GAS GAS Pages: 32
hepco & becker 501.4541 00 02 Assembling Instructions preview
501.4541 00 02
Brand: hepco & becker Pages: 6
Yamaha MT-03 Service Manual preview
MT-03
Brand: Yamaha Pages: 400
Xenith EPIC+ Manual preview
EPIC+
Brand: Xenith Pages: 7
O'Neal Commander User Manual preview
Commander
Brand: O'Neal Pages: 12
RIEJU KOSO Manual preview
KOSO
Brand: RIEJU Pages: 7
Yamaha FJR13AA Owner'S Manual preview
FJR13AA
Brand: Yamaha Pages: 114
Yamaha FJR1300R Owner'S Manual preview
FJR1300R
Brand: Yamaha Pages: 119
Yamaha FAZER FZS1000S Owner'S Manual preview
FAZER FZS1000S
Brand: Yamaha Pages: 104
Yamaha FAZER FZS600 Owner'S Manual preview
FAZER FZS600
Brand: Yamaha Pages: 108
Yamaha FJR1300 Service Manual preview
FJR1300
Brand: Yamaha Pages: 572
Yamaha FJR1300A Service Manual preview
FJR1300A
Brand: Yamaha Pages: 586
Yamaha FJR1300A(D) Service Manual preview
FJR1300A(D)
Brand: Yamaha Pages: 662
Yamaha FJR1300A(X) Service Manual preview
FJR1300A(X)
Brand: Yamaha Pages: 754
Gilera Runner 125 Manual preview
Runner 125
Brand: Gilera Pages: 80
APRILIA RSV MILLE Workshop Manual preview
RSV MILLE
Brand: APRILIA Pages: 386

Brands by name

Popular brands

Load more brands