APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 319 / 379

•

the EFI warning light turns off and the word ABS on the display disappears (NA 850 Mana

ABS).

•

the ABS warning light turns off (SL 750 Shiver ABS / Dorsoduro 750 ABS)

- if at least one malfunction is detected

•

the EFI warning light turns on permanently and the word ABS appears on the display (NA

850 Mana ABS)

•

the ABS warning light turns on permanently (SL 750 Shiver ABS / Dorsoduro 750 ABS)

The ABS system is deactivated!

The system operates perfectly just as any other braking system without ABS.

The detection of malfunctions may require more or less time according to the type of failure.

Error detection logic foresees that for the errors to be diagnosed one or more conditions must persist

within a given time.

If during this given time one of the conditions is missing but then it comes back, the timer is reset and

the system is no longer able to diagnose the error.

The ABS system is still inactive.

Example:

- error code 5D93 requires some minutes before it is diagnosed during the given time:

•

A - The EFI warning light keeps flashing with the word ABS on the display (NA 850 Mana

ABS)

•

B - The ABS warning light keeps flashing (SL 750 Shiver ABS / Dorsoduro 750 ABS)

ABS FAULTS - GUIDE TO THE DIAGNOSIS

1a.

NA 850 Mana

- ABS WARNING LIGHT + ICON 1b.

Dorsoduro 750 - SL 750 Shiver

- ABS WARN-

ING LIGHT LIT

2- CONNECT NAVIGATOR

DOES NAVIGATOR COMMUNICATE? (NO, go to 3; YES, go to 4)

3.PERFORM THESE CHECKS:

•

A. PIN 1 Ground connection

•

B. +12V at PIN 18

•

C. +12V at PIN 4 with key ON

ARE THERE ANY ERRORS? (YES, go to 5; NO, go to 6)

5. CONSULT THE ERRORS TABLE

6. ABS WARNING LIGHT ACTIVATION

ACTIVE?(YES, go to 7; NO, go to 8)

7. CONTACT TECHNICAL SERVICE

8. CHECK:

DORSODURO FACTORY ABS

Braking system

BRAK SYS - 319

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands