manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 114

Lights list

Front headlamp

Characteristic

Front daylight running light

12V - 6W H6

Low beam light

12 V - 50 W H4

High beam light

12 V - 60 W H4

Rear light

Characteristic

Rear daylight running light / stop light

LED

Fuses

AUXILIARY FUSES

A - Coil, Light logic relay, Recovery logic relay,

Stop, Horn, Tail lights, License plate light (10A).

B - Low-beam / high-beam lights (15A).

C - Live positive lead to EFG-1x control unit and to

instrument panel, Instrument panel diagnosis (10

A).

D - Instrument battery positive and EFG-1x control

unit (15 A).

E - Permanent positive, ECU power supply (3A).

F - Oxygen sensor heater, Coils, Start-up logic,

Fan and injection relay, Fuel pump, Purge valve,

Injectors, ECU, Start-up logic (20A).

G - Spare fuses (10 - 15 - 20 A)

MAIN FUSES

H - Spare fuses (30 A)

I - Battery charging, fan relay, live positive (30 A)

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 114

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands