APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 296 / 379

EAR

WHEEL

pos.

Description

Type

Quantity

Torque

Notes

Lower self-locking nut fastening

sprocket to sprocket carrier

M10

50 Nm (36.88 lbf ft)

TCEI screw fastening flexible cou-

pling mounting on wheel

M10x30

50 Nm (36.88 lbf ft)

Loctite 270

Removing the rear wheel

•

Place the vehicle on its rear service

stand.

•

Fasten the vehicle handlebar to the

bench using belts.

•

To facilitate operations, it is advisable

to remove the chain protection by un-

doing the two screws.

•

Fully slacken the gearing chain ten-

sion.

•

Make the wheel move forward and re-

lease the gearing chain from the crown

gear.

Suspensions

DORSODURO FACTORY ABS

SUSP - 296

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands