APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 168 / 379

It allows communication between the Marelli injection control unit, the throttle control unit and the in-

strument panel.

Level in electrical circuit diagram:

CAN line

Pin-out:

see wiring diagram

NAVIGATOR: ELECTRICAL ERRORS

U1602 CAN line without signals

- Bus Off.

Error cause

•

No communication on CAN line (PIN 20 and/or PIN 51 VEHICLE): problem on the whole

network (for example, battery cut-off or short circuited or shorted to ground).

Troubleshooting

•

Check the Marelli control unit VEHICLE connector: if not OK, restore; if OK, check the ground

insulation of the two CAN lines from PIN 20 and PIN 51 of the VEHICLE connector: If not

OK, restore the cable harness; if OK, check continuity of the two CAN lines from the Marelli

control unit VEHICLE connector to the filter box large connector and to the instrument panel

connector: if not OK, restore the cable harness; if OK, check that the two lines are not shorted

to positive testing each of the 3 connectors (Marelli control unit connector, filter box large

connector and instrument panel connector) with 1 connector disconnected at a time and by

setting the key to ON: If not OK, restore; if OK, replace the Marelli control unit.

Mute Node CAN Line, U1601

- Mute Node

Error cause

•

The injection ECU cannot send CAN signals; it receives signals from the instrument panel

and the throttle control unit: the control unit may need replacing.

Troubleshooting

•

Replace the Marelli control unit.

CAN line to instrument panel, U1701

- no signal

Error cause

•

No signal is received from the instrument panel.

Troubleshooting

•

Check the connector of the instrument panel: if not OK, restore; if OK, check the continuity

of the two lines from the instrument panel connector to the VEHICLE connector of the Marelli

control unit: if not OK, restore the cable harness; if OK, replace the instrument panel.

CAN line to the throttle control unit, U1705

- no signal

Error cause

•

No signal is received by the throttle control unit.

Troubleshooting

Electrical system

DORSODURO FACTORY ABS

ELE SYS - 168

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands