APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 87 / 379

•

61 - REPLACE THE START-UP RELAY 36 - END

•

62 - REPLACE THE STARTER MOTOR - END

•

63 - RESTORE THE CABLE HARNESS - END

•

64 - WHAT DOES THE "FALL SENSOR" STATUS ON NAVIGATOR (DEVICE STATUS/

ICON "0/1" SCREEN PAGE) MEAN?

If "NORMAL" is shown, go to 65; If "TIP OVER" is shown, go to 68

•

65 - WITH THE SWITCH SET TO "RUN", WHAT DOES THE "RUN-STOP SWITCH" STA-

TUS ON NAVIGATOR ("DEVICE STATUS/ICON "0/1" SCREEN PAGE) MEAN?

If "RUN" is shown, go to 66; If "STOP" is shown, go to 67

•

66 - USING NAVIGATOR CHECK THAT THE SIDE STAND, NEUTRAL SENSOR AND

CLUTCH SENSOR FUNCTION CORRECTLY; OPERATE ANY DEVICE AND CHECK THE

SUITABLE INDICATION ON THE "DEVICE STATUS/ICON "0/1" SCREEN PAGE

If "MALFUNCTION" is shown, go to 71; If "CORRECT OPERATION" is shown, go to 72

•

67 - REFER TO THE CHAPTER ON "ELECTRICAL SYSTEM/CHECKS AND CONTROLS/

FALL SENSOR; INDICATION ON NAVIGATOR ALWAYS STOP- END

•

68 - IS THE SENSOR VERTICAL?

YES, go to 69; NO, go to 70

•

69 - REFER TO THE CHAPTER ON "ELECTRICAL SYSTEM/CHECKS AND CONTROLS/

FALL SENSOR, INDICATION ON NAVIGATOR ALWAYS TIP OVER - END

•

70 - SET THE SENSOR TO THE CORRECT POSITION - END

•

71 - ACCORDING TO THE FAILURE, REFER TO CHAPTER ON "ELECTRICAL SYSTEM/

CHECKS AND CONTROLS/GEAR IN NEUTRAL SENSOR", or "CLUTCH LEVER SEN-

SOR" or "SIDE STAND SENSOR" - END

•

72 - REPLACE THE CONTROL UNIT - END

DORSODURO FACTORY ABS

Troubleshooting

TROUBL - 87

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands