APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 139 / 379

background image

•

Shorted to positive: disconnect the probe connector and check the sensor correct resistance:

replace the sensor if not OK; if it is OK, restore the cable harness.

•

circuit is open, shorted to negative: check the continuity from probe connector (PIN 3 and

4) towards the probe: if not OK, replace the probe; if it is correct, check the sensor connector

and the Marelli control unit connector. If not OK, restore. If OK, and with key set to ON and

sensor connector disconnected, check if there is battery voltage at PIN 4: if not ok, check

the red/black cable between the probe connector and the auxiliary injection relay (No. 40 in

the wiring diagram, located under the fuel tank, right side, second relay starting from the

front; CHECK, however, the identification of the relay with the colour of the cables). If there

are also coil and injector errors, check the relay and its excitation and power line; if there is

voltage at PIN 4, check the grey/blue cable ground insulation (PIN 3): if not OK, restore the

cable harness. If it is OK, check the continuity of the grey/blue cable (between the sensor

connector PIN 3 and the ENGINE PIN 32) and restore the cable harness.

NAVIGATOR: LOGIC ERRORS

Lambda probe P0134

- voltage without variation.

Error cause

•

An abnormal behaviour of the voltage at PIN 43 of the ENGINE connector has been detec-

ted: the voltage, that should vary over time, keeps a constant value instead.

Troubleshooting

•

Check circuit continuity from probe connector (PIN 1 and PIN 2) toward the probe: replace

the lambda probe if there is no continuity; if there is continuity, check the sensor connector

and the Marelli control unit connector: If not OK, restore. If OK, check continuity between

the ENGINE connector PIN 43 and PIN 60 and restore the cable harness.

CAUTION

IN CASE THE Lambda sensor correction PARAMETER, WITH ENGINE AT IDLE AND H2O T >90
°C, WHICH IS NOT WITHIN THE 0.9 - 1.1 RANGE, WITHOUT ERRORS, CHECK:
- IF < 0.9, THE PROBE READS LEAN COMBUSTION CONDITIONS AND THE CONTROL UNIT
INCREASES INJECTION TIME; CAUSES: CHECK FOR INCORRECT AIR INTAKE, LITTLE PET-
ROL, RUSTY TERMINAL CONTACTS, DEFECTIVE PROBE.
- IF > 1.1, THE PROBE READS RICH COMBUSTION CONDITIONS AND THE CONTROL UNIT RE-
DUCES INJECTION TIME; CAUSES: LITTLE AIR, EXCESSIVE PETROL, DEFECTIVE PROBE.

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 139

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
137
138
139
140
141
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: LAZER Pages: 13

Brand: Baja motorsports Pages: 8

Brand: Yukon Trail Pages: 24

Brand: KYMCO Pages: 69

Brand: VIKING BAGS Pages: 2

Stealth Air Cleaner Kit

Brand: S&S Cycle Pages: 4

Brand: Ducati Pages: 77

Multistrada 620

Brand: Ducati Pages: 382

STAR XV19CSX(C)

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 100

Star XV250B 2011

Brand: Yamaha Pages: 98

Brand: DYNATEK Pages: 12

Brand: Shark Pages: 18

Brand: SpeedAngle Pages: 37

Brand: Memphis Shades Pages: 2

Brand: Memphis Shades Pages: 2

Brand: Memphis Shades Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands