manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 303

•

Slide off the rear calliper holding plate,

keeping it linked to the brake pipe.

CAUTION

DO NOT ACTUATE ON THE REAR BRAKE LEVER AFTER
REMOVING THE WHEEL. OTHERWISE, THE CALLIPER
PLUNGERS COULD GO OUT OF THEIR SEAT, RESULTING
IN BRAKE FLUID LEAKAGE.

•

Undo and remove the two lower swing-

arm screws.

•

Remove the cable guides.

•

Undo and remove the shock absorber

lower screw and collect the nut.

•

Fasten the shock absorber to the chas-

sis.

•

With the specific box-spanner, un-

screw and remove the locking ring nut.

DORSODURO FACTORY ABS

Chassis

CHAS - 303

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands