APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download | Manualshive

Page: 157 / 379

background image

control unit connector and the correct connection of the cables on the terminals. If they are

not correct, restore the cable harness; if OK, check the cable continuity between the sensor

connector and ENGINE connector PIN 16: if there is no continuity, restore the cable harness.

If there is, replace the instrument panel if the vehicle performance is correct (the engine

starts with gear in neutral but the neutral warning light is off) or replace the control unit if the

vehicle performance is not correct (the engine does not start with gear in neutral).

•

Indication on the instrument panel always gear in neutral: disconnect the terminals from the

sensor and check if there is continuity between the ground connection and the PIN towards

the sensor, with gear engaged: if there is continuity, replace the sensor. If it is insulated from

the ground connection, it means that the green/black cable from sensor PIN 1 to ENGINE

connector PIN 16 is shorted to ground: restore the cable harness

Clutch lever sensor

CLUTCH LEVER SENSOR

Function

It tells the clutch lever position to the control unit.

Operation / Operating principle

If there is gear engaged but the clutch is pulled, i.e. circuit closed to ground, vehicle start-up is not

enabled.

Level in electrical circuit diagram:

Start-up enabling switches.

Location:

•

on the vehicle: under clutch lever

•

connector: behind the instrument panel

Electrical characteristics:

•

Clutch pulled: closed circuit (continuity)

•

Clutch released: open circuit (infinite resistance)

Pin-out:

1. Voltage 12V

2. Ground connection

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: STATUSES

Clutch

Example value:

Indefinite - released - pulled

The statuses regularly viewed are Released / Pulled

Troubleshooting:

DORSODURO FACTORY ABS

Electrical system

ELE SYS - 157

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
155
156
157
158
159
...
»

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO FACTORY ABS 2011

Brand: Yamaha Pages: 662

Brand: hepco & becker Pages: 4

690 Enduro R AU/GB 2014

Brand: KTM Pages: 18

Brand: hepco & becker Pages: 4

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 114

YZF-R1P 2001-2003

Brand: Yamaha Pages: 439

Brand: Kemppi Pages: 10

Scorpion 608-30-10086

Brand: Barnett Pages: 2

Brand: Rally-Raid Pages: 2

Brand: R&G Pages: 6

Brand: R&G Pages: 6

Brand: R&G Pages: 6

Brand: R&G Pages: 9

Brand: R&G Pages: 22

Brand: R&G Pages: 20

Brand: R&G Pages: 24

Brand: R&G Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands