manualshive.com logo in svg

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Share
Download
APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download Page 372

- Response to throttle control

- Stability when accelerating and braking

- Front and rear brake efficiency

- Front and rear suspension efficiency

- Abnormal noise

Static test

Static check after test drive:

- Restarting when warmed up

- Starter operation (if present)

- Minimum holding (turning the handlebar)

- Uniform turning of the steering

- Possible leaks

- Radiator electric fan operation (if present)

Functional inspection

- Hydraulic braking system

- Stroke of brake and clutch levers (if present)

- Clutch - Check for correct operation

- Engine - Check for correct general operation and absence of abnormal noise

- Other

- Documentation check:

- Chassis and engine numbers check

- Supplied tools check

- License plate fitting

- Locks checking

- Tyre pressure check

- Installation of mirrors and any possible accessories

NEVER EXCEED THE RECOMMENDED INFLATION PRESSURES AS TYRES MAY BURST.

CAUTION

CHECK AND ADJUST TYRE PRESSURE WITH TYRES AT AMBIENT TEMPERATURE.

Pre-delivery

DORSODURO FACTORY ABS

PRE DE - 372

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands