APRILIA DORSODURO FACTORY ABS 2011 Service Station Manual Download

Page: 173 / 379

ENGINE

pos.

Description

Type

Quantity

Torque

Notes

Flanged TE screw fastening pinion

M10x1.25x25

50 Nm (36.88 lbf ft)

Loctite 270

TCEI screw fastening Pin to gearbox

lever and Gearbox Lever to knurled

shaft

M6x16

10 Nm (7.37 lbf ft)

LH locknut for ball joint

10 Nm (7.37 lbf ft)

RH locknut for ball joint

10 Nm (7.37 lbf ft)

Screw fastening engine bracket /

clutch side crankcase half

12 Nm (8.85 lbf ft)

Map sensor union (brass)

2 Nm (1.48 lbf ft)

Loctite 243

Map sensor union (steel)

3.50 Nm (2.58 lbf ft)

Loctite 243

LH ball joint on gearbox control lever

10 Nm (7.37 lbf ft)

Loctite 243

RH ball joint on gearbox control lever

10 Nm (7.37 lbf ft)

Loctite 243

Fastener for positive cable on engine

10 Nm (7.37 lbf ft)

TE screw fastening negative cable to

engine

M6x12

10 Nm (7.37 lbf ft)

Vehicle preparation

•

Remove the air filter box.

•

Remove the coolant radiator.

•

Remove the exhaust system.

•

Place the optional under-sump and

rear wheel service stands.

•

Undo and remove the screw and move

the coil.

DORSODURO FACTORY ABS

Engine from vehicle

ENG VE - 173

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO FACTORY ABS 2011




























































































































































































































































































































































































Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands

APRILIA DORSODURO FACTORY ABS 2011, Service Station Manual

Search results

Summary of Contents for DORSODURO FACTORY ABS 2011

Reviews:

Related manuals for DORSODURO FACTORY ABS 2011

Brands by name

Popular brands