Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 650

Страница: 650 / 1056

Turn the engine switch off.

Inspect for poor connection (such
as damaged/pulled-out terminals,

corrosion).

Are there any malfunction?

Go to the next step.

INSPECT GENERATOR CIRCUIT
FOR OPEN CIRCUIT

Inspect for continuity between
generator terminal LI (wiring

harness-side) and PCM terminal
2AG (wiring harness-side)

Is there continuity?

Yes

Go to the next step.

Repair or replace suspected part, then go to

Step 12.

INSPECT BATTERY POSITIVE

TERMINAL FOR POOR
INSTALLATION

Turn the engine switch off.

Inspect the battery positive
terminal for looseness.

Is there any malfunction?

Yes

Connect the battery positive terminal

correctly, then go to Step 12.

Go to the next step.

INSPECT GENERATOR CIRCUIT

FOR OPEN CIRCUIT

Inspect continuity between

generator terminal B (wiring
harness-side) and battery positive

terminal (wiring harness-side).

Is there continuity?

Yes

Go to the next step.

Repair or replace suspected part, then go to
Step 12.

INSPECT GENERATOR

Inspect the generator.

(see

GENERATOR

INSPECTION [MZI-3.5]

Is there any malfunction?

Yes

Replace the generator, then go to the next
step.

(see

GENERATOR

REMOVAL/INSTALLATION [MZI-

3.5]

Go to the next step.

VERIFY TROUBLESHOOTING OF

DTC P0620 HAS BEEN
COMPLETED

Verify that all disconnected

connectors reconnected.

Clear the DTC from the PCM

Yes

Replace the PCM, then go to the next step.

(see

PCM

REMOVAL/INSTALLATION [MZI-

3.5]

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:35 AM

Page 303

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды