Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 536

Страница: 536 / 1056

disconnected.

Turn the ignition switch to the ON

position (Engine running).

With the engine running,
determine if the generator is still

noisy.

Does the noise remain constant
when the terminal B is

disconnected?

INSPECT CMP SENSOR (RH)
CONNECTOR FOR POOR

CONNECTION

Turn the ignition switch off.

Disconnect the CMP sensor (RH)

connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Are there any malfunction?

Yes

Repair or replace suspected part, then go
to Step 11.

Go to the next step.

INSPECT CMP SENSOR SIGANAL
CIRCUIT FOR SHORT TO POWER

SUPPLY

Turn the ignition switch to the ON

position (Engine off).

Measure voltage between CMP
sensor (RH) terminal A (wiring

harness-side) and body ground.

Is the voltage

B+

Yes

Repair or replace suspected part, then go
to Step 11.

Go to the next step.

INSPECT CMP SENSOR (RH)
SIGNAL CIRCUIT FOR SHORT TO

GROUND

Turn the ignition switch off.

Check continuity between CMP

sensor (RH) terminal A and body
ground.

Is there continuity?

Yes

Repair or replace suspected part, then go
to Step 11.

Go to the next step.

INSPECT PCM CONNECTOR FOR
POOR CONNECTION

Turn the ignition switch off.

Yes

Repair or replace suspected part, then go
to Step 11.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:32 AM

Page 189

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды