manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DIAGNOSTIC PROCEDURE 

DIAGNOSTIC PROCEDURE

 

POSSIBLE CAUSE

 

z

Fuel vapor is hazardous. It can easily ignite, causing serious injury 
and damage. Always keep sparks and flames away from fuel.  

z

Fuel line spills and leakage are dangerous. Fuel can ignite and 

cause serious injuries or death and damage. Fuel can also irritate 
skin and eyes. To prevent this, always complete "BEFORE REPAIR 

PROCEDURE" and "AFTER REPAIR PROCEDURE" described in 
this manual. 

(see BEFORE REPAIR PROCEDURE [MZI-3.5] .) 

(see AFTER REPAIR PROCEDURE [MZI-3.5] .) 

CAUTION:

z

Disconnecting/connecting quick release connector without 

cleaning it may cause damage to fuel pipe and quick release 
connector. Always clean quick release connector joint area before 

disconnecting/connecting, and make sure that it is free of foreign 
material.  

STEP INSPECTION

RESULTS ACTION

1

Visually inspect for fuel leakage at 

fuel injector O-ring and fuel line. 
Service if necessary. 

Install the fuel pressure gauge between 
the fuel pipe and the fuel distributor. 

Start engine and idle it. 

Measure fuel line pressure during idle.
Is fuel line pressure correct during 

idle? 
(see 

FUEL LINE PRESSURE 

INSPECTION [MZI-3.5]

 .)

Yes

Go to the next step.

No

Replace the fuel pump unit. 
(see 

FUEL PUMP UNIT 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

2

Inspect for blockage/restriction or 
open circuit in wiring harness between 

the engine vacuum port and the 
charcoal canister. 

Inspect for blockage in fuel tank vent 
system. 

Is malfunction indicated?

Yes

Replace vacuum hose.

No

Go to the next step.

3

Inspect the purge solenoid valve. 

(see 

PURGE SOLENOID VALVE 

INSPECTION [MZI-3.5]

 .) 

Is the solenoid operating properly?

Yes

Go to the next step.

No

Replace the purge solenoid valve. 

(see 

PURGE SOLENOID VALVE 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:37 AM

Page 75 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

cam 2850 Mounting Instructions preview
2850
Бренд: cam Страницы: 2
Dapper Lighting 575 Install Manual preview
575
Бренд: Dapper Lighting Страницы: 2
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Бренд: Tesla Страницы: 9
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Бренд: Waeco Страницы: 212
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Бренд: Romik Страницы: 6
Subaru 2007 Impreza Brochure & Specs preview
2007 Impreza
Бренд: Subaru Страницы: 21
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Бренд: GMC Страницы: 120
Prime Tech H-066 User Manual preview
H-066
Бренд: Prime Tech Страницы: 6
Whispbar K919W Fitting Instructions Manual preview
K919W
Бренд: Whispbar Страницы: 17
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Бренд: ULTIMATE SPEED Страницы: 6
Velleman CARS4500 User Manual preview
CARS4500
Бренд: Velleman Страницы: 12
Meta System 900000358 Installation Technical Sheet preview
900000358
Бренд: Meta System Страницы: 22
Oldsmobile 2003 Alero Owner'S Manual preview
2003 Alero
Бренд: Oldsmobile Страницы: 354
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Бренд: ULTIMATE SPEED Страницы: 40
rockymounts SplitRailLS Installation Instructions Manual preview
SplitRailLS
Бренд: rockymounts Страницы: 6
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Бренд: N-Com Страницы: 36
BMW 84 61 0 028 926 Installation Instructions Manual preview
84 61 0 028 926
Бренд: BMW Страницы: 13
Roadtrek SS Agile 2017 Owner'S Manual preview
SS Agile 2017
Бренд: Roadtrek Страницы: 61

Бренды по названию

Популярные бренды

Загрузить еще бренды