manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

8

INSPECT PCM CONNECTOR FOR 
POOR CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect PCM connector.  

z

Inspect for poor connection (such 
as damaged/pulled-out pins, 

corrosion).  

z

Is there any malfunction?  

Yes

Repair or replace suspected part, then go to 
Step 10.

No

Go to the next step.

9

INSPECT FAN CONTROL 

CIRCUIT FOR OPEN CIRCUIT

 

z

Inspect continuity between the 
following circuits: 

Dual fan control module

  

{

Fan control module No.1 
terminal 1B (wiring 

harness-side) and PCM 
terminal 1AM (wiring 

harness-side).  

{

Fan control module No.2 
terminal B (wiring harness-

side) and PCM terminal 
1AM (wiring harness-side).  

Single fan control module

  

{

Fan control module terminal 
1B (wiring harness-side) 

and PCM terminal 1AM 
(wiring harness-side).  

z

Are there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 
the next step.

10

VERIFY TROUBLESHOOTING OF 
DTC P0480 HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 
connectors reconnected.  

z

Clear the DTC from the PCM 

memory using the M-MDS.  

z

Perform the "KOEO or KOER 

self-test". 

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:33 AM

Page 255 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Camcar 40104 Mounting Instructions preview
40104
Бренд: Camcar Страницы: 6
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Бренд: Eaton Страницы: 12
Fab Fours BLACK STEEL S2560 Installation Instructions Manual preview
BLACK STEEL S2560
Бренд: Fab Fours Страницы: 9
Aries P35-2004 Installation Manual preview
P35-2004
Бренд: Aries Страницы: 3
Cadillac 2012 Escalade Hybrid Manual preview
2012 Escalade Hybrid
Бренд: Cadillac Страницы: 90
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Axxess AX-AM-AU92 Installation Instructions Manual preview
AX-AM-AU92
Бренд: Axxess Страницы: 8
EEZ RV 51 SC Instruction Manual preview
51 SC
Бренд: EEZ RV Страницы: 31
Acura 2006 TSX Owner'S Manual preview
2006 TSX
Бренд: Acura Страницы: 2
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
Rostra RearSight 250-8308 Installation Instructions preview
RearSight 250-8308
Бренд: Rostra Страницы: 2
Skoda Fabia Combi 5J Fitting Instructions preview
Fabia Combi 5J
Бренд: Skoda Страницы: 2
Renault KANGOO BE BOP Driver'S Handbook Manual preview
KANGOO BE BOP
Бренд: Renault Страницы: 198
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Бренд: T.J.M. Страницы: 18
Audi PXDXVW3 Quick Start Manual preview
PXDXVW3
Бренд: Audi Страницы: 4
Tesla Gen 3 Manual preview
Gen 3
Бренд: Tesla Страницы: 42
APS iBoard IB-R159 Manual preview
iBoard IB-R159
Бренд: APS Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды