manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

CYLINDER HEAD TEMPERATURE (CHT) SENSOR INSPECTION [MZI-3.5]

RESISTANCE INSPECTION 

1. Disconnect the CHT sensor connector.  
2. Measure the resistance between the CHT sensor terminals. 

z

If it is not within the specification, replace the CHT sensor.  

z

If the monitor item status/specification (reference) is not within the specification, even though the 

resistance is within the specification, perform the "Circuit Open/Short Inspection".  

Measure the cylinder head temperature sensor resistance (approx.).

  

CYLINDER HEAD TEMPERATURE SENSOR RESISTANCE REFERENCE

 

Cylinder head temperature sensor characteristics graph (reference) 

Fig. 37: Cylinder Head Temperature Sensor Characteristics Graph

 

Courtesy of MAZDA MOTORS CORP.

 

CIRCUIT OPEN/SHORT INSPECTION 

NOTE:

z

Before performing the following inspection, make sure to follow the 

procedure as indicated in the troubleshooting flowchart. (see HOW TO 
USE THIS MANUAL .)  

Cylinder head temperature (°C {°F})

Resistance (kilohm)

20 {68}

37.387

80 {176}

3.775

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:25:31 AM

Page 40 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Jackco SHARP ALIGN User Manual preview
SHARP ALIGN
Бренд: Jackco Страницы: 11
Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Бренд: Jeep Страницы: 1311
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Бренд: Victory 4x4 Страницы: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Бренд: Keith Страницы: 2
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Бренд: Tessera4x4 Страницы: 20
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Actia SmarTach Manual preview
SmarTach
Бренд: Actia Страницы: 102
tams elektronik 54-01016 Manual preview
54-01016
Бренд: tams elektronik Страницы: 44
ORA XL MIRROR Installation Instructions Manual preview
XL MIRROR
Бренд: ORA Страницы: 7
Carcomm CMPC-22 Fujitsu-Siemens PocketLoox 410 Installation Manual preview
CMPC-22 Fujitsu-Siemens PocketLoox 410
Бренд: Carcomm Страницы: 2
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Бренд: Acura Страницы: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Бренд: Ford Страницы: 325
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Бренд: AUTOTECH Страницы: 4
Crux RVCFD-79 Manual preview
RVCFD-79
Бренд: Crux Страницы: 10
Wald Black Bison Sports Series Installation Manual preview
Black Bison Sports Series
Бренд: Wald Страницы: 7
Kuda 050130 Installation Instruction preview
050130
Бренд: Kuda Страницы: 4
Rhino-Rack RBC044 Installation Instructions preview
RBC044
Бренд: Rhino-Rack Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды