manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

z

Turn the ignition switch off.  

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Access the PCM and monitor the 

HO2S signal PID.  

z

Perform a thorough wiggle test on 
the HO2S wiring harness.  

z

Does the voltage change during 

the wiggle test?  

No

Perform the "INTERMITTENT 
CONCERN TROUBLESHOOTING". 

Then go to the next step.

6

INSPECT HO2S CIRCUIT FOR 
SHORT TO POWER SUPPLY IN 

WIRING HARNESS

 

z

Turn the ignition switch off.  

z

Disconnect the PCM connector.  

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Measure the voltage between 
HO2S terminal B and body 

ground.  

z

Is any voltage present?  

Yes

Repair or replace suspected part, Then go 
to the next step.

No

Go to Step 9.

7

INSPECT HO2S

 

z

For DTC P0132 Inspect the front 

HO2S(RH)  

z

For DTC P0138 Inspect the rear 
HO2S(RH)  

z

For DTC P0152 Inspect the front 

HO2S(LH)  

z

For DTC P0138 Inspect the rear 
HO2S(LH) 

(see 

FRONT HEATED 

OXYGEN SENSOR (HO2S) 

INSPECTION [MZI-3.5].

 ) 

(see 

REAR HEATED OXYGEN 

SENSOR (HO2S) INSPECTION 

[MZI-3.5].

 ) 

z

Is there any malfunction?  

Yes

Replace the HO2S. 

(see 

FRONT HEATED OXYGEN 

SENSOR (HO2S) 

REMOVAL/INSTALLATION [MZI-
3.5].

 ) 

(see 

REAR HEATED OXYGEN 

SENSOR (HO2S) 

REMOVAL/INSTALLATION [MZI-
3.5].

 ) 

Then go to the next step.

No

Go to the next step.

8

INSPECT FOR CORRECT PCM 

OPERATION

 

Yes

Go to the next step.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:30 AM

Page 88 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Davis Instruments 8127 Installation Instructions Manual preview
8127
Бренд: Davis Instruments Страницы: 16
Lancia Y Owner'S Handbook Manual preview
Y
Бренд: Lancia Страницы: 191
AAMP of America iSimple Operation Manual preview
iSimple
Бренд: AAMP of America Страницы: 6
Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Бренд: Jeep Страницы: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Бренд: Jeep Страницы: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Бренд: Jeep Страницы: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Бренд: Jeep Страницы: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Бренд: Jeep Страницы: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Бренд: Jeep Страницы: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Бренд: Jeep Страницы: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Бренд: Jeep Страницы: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Бренд: Jeep Страницы: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Бренд: Jeep Страницы: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Бренд: Jeep Страницы: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Бренд: Jeep Страницы: 4
Jeep Jeep Wrangler Owner'S Manual Supplement preview
Jeep Wrangler
Бренд: Jeep Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды