manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя, Страница: 351 / 1056

Поделиться
Скачать
Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 351

ON-BOARD SYSTEM READINESS TESTS ACCESS PROCEDURE

1. Connect the M-MDS to the DLC-2.  
2. After the vehicle is identified, select the following items from the initial screen of the M-MDS. 

z

When using the IDS (laptop PC) 

1. Select the "Toolbox" tab.  
2. Select "Powertrain".  
3. Select "OBD Test Modes".  
4. Select "Mode 1 Powertrain Data".  
5. Select "PCM".  

z

When using the PDS (Pocket PC) 

1. Select "OBDII Modes".  
2. Select "Mode 1 Powertrain Data".  
3. Select "PCM".  

3. Then, select the "***SUP" and "**EVAL" PIDs in the PID selection screen.  
4. Monitor those PIDs and check it system monitor is completed. 

Fig. 5: Identifying DLC-2 Connector

 

Courtesy of MAZDA MOTORS CORP.

 

PID/DATA MONITOR AND RECORD PROCEDURE 

NOTE:

z

If the on-board system readiness tests are not completed the PCM 
stores DTC P1000.  

NOTE:

z

The PID/DATA MONITOR function monitors the calculated value of the 
input/output signals in the PCM. Therefore, an output device malfunction 

is not directly indicated as a malfunction of the monitored value for the 

output device. If a monitored value of an output device is out of 
specification, inspect the monitored value of the input device related to the 

output control.  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:28 AM

Page 4 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов