Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 238

Страница: 238 / 1056

1. Assemble the camshaft timing chain tensioners on both sides.

Tightening torque

8.5-11.5 N.m {87-117 kgf.cm, 76-101 in.lbf}

2. Install the camshaft component (RH).

1. Install the camshaft timing chain by aligning the colored links on the camshaft timing chain with

the marks on the camshaft sprockets (RH).

Fig. 69: Aligning Colored Links On Camshaft Timing Chain With Marks On Camshaft

Sprockets

Courtesy of MAZDA MOTORS CORP.

2. Position the camshaft component onto the cylinder head (RH) in the neutral position as shown.

NOTE:

Install the camshaft, camshaft sprocket and camshaft timing chain of

the both bank as a single unit.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 47

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды