Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 326

Страница: 326 / 1056

Fig. 51: Identifying Fuel Injector Atomization Pattern

Courtesy of MAZDA MOTORS CORP.

PRESSURE REGULATOR INSPECTION [MZI-3.5]

1. Perform "FUEL LINE PRESSURE INSPECTION". (See

FUEL LINE PRESSURE INSPECTION

[MZI-3.5]

NOTE:

Due to the adoption of the mechanical returnless fuel system, the pressure

regulator cannot be inspected separately.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Fuel System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:24:13 AM

Page 38

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды