Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 133

Страница: 133 / 1056

If there is no continuity, there is an open circuit. Repair or replace the wiring harness.

{

PCV valve heater fitting terminal A and main relay No.1 terminal D

{

PCV valve heater fitting terminal B and PCM terminal 2AU

Short circuit

If there is continuity, there is a short circuit. Repair or replace the wiring harness.

{

PCV valve heater fitting terminal A and power supply

{

PCV valve heater fitting terminal A and body ground

{

PCV valve heater fitting terminal B and power supply

{

PCV valve heater fitting terminal B and body ground

ROLLOVER VALVE REMOVAL/INSTALLATION [MZI-3.5]

ROLLOVER VALVE INSPECTION [MZI-3.5]

1. Perform the fuel tank inspection. (see

FUEL TANK INSPECTION [MZI-3.5]

FUEL SHUT-OFF VALVE REMOVAL/INSTALLATION [MZI-3.5]

FUEL SHUT-OFF VALVE INSPECTION [MZI-3.5]

1. Perform the fuel tank inspection. (see

FUEL TANK INSPECTION [MZI-3.5]

QUICK RELEASE CONNECTOR (EMISSION SYSTEM)

REMOVAL/INSTALLATION [MZI-3.5]

NOTE:

The rollover valve cannot be removed as it is built into the fuel tank.

NOTE:

The rollover valve cannot be disassembled and inspected as it is built into
the fuel tank.

NOTE:

The fuel shut-off valve cannot be removed as it is built into the fuel tank.

NOTE:

The fuel shut-off valve cannot be removed and inspected as it is built into
the fuel tank.

WARNING:

Fuel is very flammable liquid. If fuel spills or leaks from the
pressurized fuel system, it will cause serious injury or death and

facility breakage. Fuel can also irritate skin and eyes. To prevent

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Emission System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:24:50 AM

Page 18

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды