Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 729

Страница: 729 / 1056

VERIFY RELATED REPAIR
INFORMATION AVAILABILITY

Verify related Service Bulletins
and/or on-line repair information

availability.

Is any related Service Bulletins
available?

Yes

Perform repair or diagnosis according to
available Service Bulletins.

If vehicle is not repaired, go to next
step.

Go to the next step.

INSPECT PSP SWITCH

CONNECTOR FOR POOR
CONNECTION

Turn the ignition switch off.

Disconnect the PCM connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Is there any malfunction?

Yes

Repair or replace suspected part, then go to

Step 8.

Go to the next step.

INSPECT PSP SWITCH CIRCUIT

FOR SHORT TO GROUND

Turn the ignition switch off.

Inspect for continuity between
PSP switch terminal A (wiring

harness-side) and body ground.

Is there continuity?

Yes

Repair or replace suspected part, then go to

Step 8.

Go to the next step.

INSPECT PCM CONNECTOR FOR

POOR CONNECTION

Turn the ignition switch off.

Disconnect the PCM connector.

Inspect for poor connection (such
as damaged/pulled-out pins,

corrosion).

Is there any malfunction?

Yes

Repair or replace suspected part, then go to

Step 8.

Go to the next step.

INSPECT PSP SWITCH CIRCUIT

FOR OPEN CIRCUIT

Inspect for continuity between
PSP switch terminal A (wiring

harness-side) and PCM terminal 2I
(wiring harness-side)

Is there continuity?

Yes

Go to the next step.

Repair or replace suspected part, then go to
Step 8.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:37 AM

Page 382

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды