Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 9

Страница: 9 / 1056

Fig. 9: Identifying Throttle Body Connector Terminals

CIRCUIT OPEN/SHORT INSPECTION

1. Disconnect the PCM connector.
2. Inspect the following wiring harnesses for open or short (continuity check).

Fig. 10: Identifying Throttle Body Connector Terminals

Fig. 11: Identifying PCM Connector Terminals

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Intake-Air System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:23:32 AM

Page 9

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды