Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 907

Страница: 907 / 1056

DIAGNOSTIC PROCEDURE

Fuel line spills and leakage are dangerous. Fuel can ignite and
cause serious injuries or death and damage. Fuel can also irritate

skin and eyes. To prevent this, always complete "BEFORE REPAIR
PROCEDURE" and "AFTER REPAIR PROCEDURE" described in

this manual.

(see BEFORE REPAIR PROCEDURE [MZI-3.5] .)

(see AFTER REPAIR PROCEDURE [MZI-3.5] .)

CAUTION:

Disconnecting/connecting quick release connector without
cleaning it may cause damage to fuel pipe and quick release

connector. Always clean quick release connector joint area before
disconnecting/connecting, and make sure that it is free of foreign

material.

STEP INSPECTION

RESULTS ACTION

Remove all the spark plugs.

Inspect spark plug condition.
Is spark plug condition normal?

Yes

Troubleshooting completed.

Specific plug is wet or covered with

carbon:

Go to the next step.

Specific plug looks grayish white:

Go to Step 7.

All plugs are wet or covered with
carbon:

Go to Step 9.

All plugs look grayish white:

Go to Step 15.

Are the spark plug wet/covered with

carbon by the engine oil?

Yes

Inspect all areas related to oil, working

up and down.

Go to the next step.

Inspect the spark plug for the
following:

Cracked insulator

Heat range

Air gap

Worn electrode

Is the spark plug normal?

Yes

Go to the next step.

Replace the spark plug.
(see

SPARK PLUG

REMOVAL/INSTALLATION [MZI-
3.5]

)

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:38 AM

Page 90

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды