Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 57

Страница: 57 / 1056

CONNECTORS

CONNECTORS LOCATION

Passenger-Side Air Bag Module No.1

Behind right side of dash.

Passenger-Side Air Bag Module No.2

Behind right side of dash.

Passenger-Side Curtain Air Bag Module

Top of right "C" pillar.

Passenger-Side Pre-Tensioner Seat Belt

Base of right "B" pillar.

Passenger-Side Side Air Bag Module

Right side of front passenger's seat back.

Power MOS FET

Under center console.

PVC Valve Heater Fitting

Center rear of engine compartment.

Rear Mount Camera

Left side of liftgate.

Throttle Body

Top rear of engine.

Component

Location

C-03 (12 Pin)

Left side of engine compartment. See

Fig. 6

C-05 (14 Pin)

Behind right kick panel. See

Fig. 13

C-06 (Blue, 40 Pin)

Behind left side of dash. See

Fig. 29

C-07 (14 Pin)

Under front of center console. See

Fig. 22

C-08 (16 Pin)

Under left center of center console. See

Fig. 23

C-09 (14 Pin)

Behind left kick panel. See

Fig. 39

C-10 (16 Pin)

Behind left kick panel. See

Fig. 38

C-11 (56 Pin)

Under front of center console. See

Fig. 21

C-12 (34 Pin)

Behind left kick panel. See

Fig. 47

C-13 (34 Pin)

Behind right kick panel. See

Fig. 34

C-14 (14 Pin)

At left "B" pillar. See

Fig. 54

C-15 (14 Pin)

At right "B" pillar. See

Fig. 48

C-16 (Blue, 40 Pin)

Behind left kick panel. See

Fig. 41

C-17 (16 Pin)

Behind left kick panel. See

Fig. 32

C-18 (16 Pin)

Behind left kick panel. See

Fig. 31

C-19 (14 Pin)

Under driver's seat. See

Fig. 42

C-20 (14 Pin)

Under front passenger's seat. See

Fig. 45

C-21 (Blue, 40 Pin)

At left "D" pillar. See

Fig. 63

C-23 (Light Gray, 24 Pin)

Right rear corner of vehicle. See

Fig. 52

C-24 (24 Pin)

Top of right "D" pillar. See

Fig. 56

C-25 (Blue, 39 Pin)

Behind right kick panel. See

Fig. 12

C-26 (14 Pin)

Center rear of roof. See

Fig. 58

C-27 (16 Pin)

Center rear of roof. See

Fig. 60

C-28 (6 Pin)

At left "D" pillar. See

Fig. 57

C-32 (14 Pin)

In left rear door. See

Fig. 55

C-33 (14 Pin)

In right rear door. See

Fig. 49

C-34 (16 Pin)

Top front of engine. See

Fig. 9

2007 Mazda CX-9 Grand Touring

2007 MAZDA CX-9

Microsoft

Sunday, November 15, 2009 9:30:18 AM

Page 6

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2007

Бренды по названию

Популярные бренды