Mazda CX-9 Grand Touring 2007 Скачать руководство пользователя страница 268

Страница: 268 / 1056

Fig. 122: Identifying Engine External Components With Torque Specification

Courtesy of MAZDA MOTORS CORP.

NO.3 ENGINE MOUNT STAY (ENGINE FRONT COVER SIDE) INSTALLATION NOTE

1. Tighten the No.3 engine mount stay (engine front cover side) in the order shown in the figure.

Tightening torque

21.6-30.4 N.m {2.21-3.09 kgf.m, 16.0-22.4 ft.lbf}

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:28 AM

Page 77

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы:

Mazda CX-9 Grand Touring 2007, Руководство пользователя, Страница: 268 / 1056

Результаты поиска

Содержание CX-9 Grand Touring 2007

Отзывы: