manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 

available?  

the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

the next step.  

No

Go to the next step.

3

INSPECT HO2S WIRING HARNESS 
CONNECTORS

 

z

For P0040, visually inspect the 
vehicle front HO2S wiring harness 

connector (s) for any indication of 
crossed wires (Also, stretched or 

incorrectly mounted wiring 
harnesses).  

z

For P0041, visually inspect the 

vehicle rear HO2S wiring harness 
connector (s) for any indication of 

crossed wires (Also, stretched or 
incorrectly mounted wiring 

harnesses).  

z

Are there crossed connections or 
wires?  

Yes

Repair if necessary.

No

Go to the next step.

4

VERIFY TROUBLESHOOTING OF 
DTC P0040, P0041 HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 
connectors reconnected.  

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Clear the DTC from the PCM 

memory using the M-MDS.  

z

Start the engine and run it at idle.  

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

5

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform "AFTER REPAIR 

PROCEDURE". 

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:29 AM

Page 42 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

LaserTrack Flare Installation Manual preview
Flare
Бренд: LaserTrack Страницы: 12
kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Бренд: kaarta Страницы: 29
PAC RadioPRO 5 RP5-GM41 Quick Start Manual preview
RadioPRO 5 RP5-GM41
Бренд: PAC Страницы: 3
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
Renault Lodgy 2017 Driver'S Handbook Manual preview
Lodgy 2017
Бренд: Renault Страницы: 238
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Бренд: Monacor Страницы: 2
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Бренд: TATA Motors Страницы: 136
WABCO OnSide MM16167 Maintenance Manual preview
OnSide MM16167
Бренд: WABCO Страницы: 52
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Бренд: Oldsmobile Страницы: 348
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Бренд: Black+Decker Страницы: 21
Beeper RW050RF User& Installer'S Manual preview
RW050RF
Бренд: Beeper Страницы: 20
Brigade VBV-770-310 Quick Installation Manual preview
VBV-770-310
Бренд: Brigade Страницы: 12
Reliant Rebel 700 1967 Workshop Manual preview
Rebel 700 1967
Бренд: Reliant Страницы: 116
Autoplugin RCP-B1 Installation Manual preview
RCP-B1
Бренд: Autoplugin Страницы: 8
Cadillac 2005 XLR Owner'S Manual preview
2005 XLR
Бренд: Cadillac Страницы: 438
Magneti Marelli AC911 Installation Instruction preview
AC911
Бренд: Magneti Marelli Страницы: 3
Westin 33-1920 Instructions preview
33-1920
Бренд: Westin Страницы: 3
Audi S4 Biturbo Buyer'S Manual preview
S4 Biturbo
Бренд: Audi Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды