manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

DTC P1285, P1299 [MZI-3.5] 

DTC P1285, P1299 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

z

Does the engine start?  

1 second of operation. For 

intermittent Stalls while driving, 
verify the M-MDS tester to PCM 

communication during concern. If 
a PCM communication error 

occurs, possible causes are: 

{

Loss of PWRS or grounds 
to the PCM.  

{

Malfunctioning PCM PWR 

relay.  

{

Malfunctioning EEC PWR 

diode.  

z

Repair if necessary and return the 
vehicle to customer.  

No

DTC P1260 is not the cause of the No 

Start. 
(see 

QUICK DIAGNOSTIC CHART 

[MZI-3.5]

 .)

6

VERIFY TROUBLESHOOTING OF 
DTC P1260 HAS BEEN COMPLETED

z

Verify that all disconnected 
connectors are reconnected.  

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Start the engine and run it at idle.  

z

Retrieve DTCs using the M-MDS,  

z

Is the PENDING CODE for this 

DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

7

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform "AFTER REPAIR 
PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTC present?  

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:36 AM

Page 347 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

NavLinkz CAM-N-CV133-V Manual preview
CAM-N-CV133-V
Бренд: NavLinkz Страницы: 4
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Brodit ProClip 853660 Manual preview
ProClip 853660
Бренд: Brodit Страницы: 2
Power Fist 8985988 Manual preview
8985988
Бренд: Power Fist Страницы: 12
EAL EUFAB 16491 Operating Instructions Manual preview
EUFAB 16491
Бренд: EAL Страницы: 7
Prorack K748 Fitting Instructions Manual preview
K748
Бренд: Prorack Страницы: 14
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Бренд: Tessera4x4 Страницы: 20
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Бренд: Subaru Страницы: 99
Saab 92X Owner'S Manual preview
92X
Бренд: Saab Страницы: 445
Cadillac 2007 CTS Owner'S Manual preview
2007 CTS
Бренд: Cadillac Страницы: 518
Opel OPEL INSIGNIA Infotainment Manual preview
OPEL INSIGNIA
Бренд: Opel Страницы: 141
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Бренд: Unex Страницы: 30
Abrams RE-47X Installation And Operation Manual preview
RE-47X
Бренд: Abrams Страницы: 12
Prime Design URX-001-E Assembly Instructions Manual preview
URX-001-E
Бренд: Prime Design Страницы: 8
Edelbrock 5756 Installation Instructions preview
5756
Бренд: Edelbrock Страницы: 1
Porsche 928 GTS 1994 Owner'S Manual preview
928 GTS 1994
Бренд: Porsche Страницы: 127
Metra Electronics 99-9302 Installation Instructions Manual preview
99-9302
Бренд: Metra Electronics Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды