manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Руководство пользователя

Мазда CX-9 Grand Touring 2007 - великолепное кроссовер с роскошным исполнением. Полный комплект руководств пользователя доступен для загрузки бесплатно на {сайт}. Отличное качество исполнения, комфортный салон и мощный двигатель делают этот автомобиль идеальным выбором для семьи.

Поделиться
Скачать
background image

Fig. 22: Identifying PCM Connector Terminals

Courtesy of MAZDA MOTORS CORP.

 

Open circuit 

z

If there is no continuity, there is an open circuit. Repair or replace the wiring harness. 

{

PCV valve heater control terminal A and main relay No.1 terminal D  

{

PCV valve heater control terminal B and PCM terminal 2BL  

Short circuit 

z

If there is continuity, there is a short circuit. Repair or replace the wiring harness. 

{

PCV valve heater control terminal A and power supply  

{

PCV valve heater control terminal A and body ground  

{

PCV valve heater control terminal B and power supply  

{

PCV valve heater control terminal B and body ground  

POSITIVE CRANKCASE VENTILATION (PCV) VALVE HEATER FITTING 
REMOVAL/INSTALLATION [MZI-3.5] 

1. Disconnect the negative battery cable. (see 

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

 .)  

2. Remove in the order indicated in the table. 

Fig. 23: Identifying PCV Valve Heater Fitting And Connector With Torque Specifications

 

Courtesy of MAZDA MOTORS CORP.

 

3. Install in the reverse order of removal. 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Emission System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:24:50 AM

Page 15 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2007

Harbor Freight Tools 92043 Assembly And Operating Instructions preview
92043
Бренд: Harbor Freight Tools Страницы: 4
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Бренд: Saleen Страницы: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Бренд: Buick Страницы: 5
Carcomm CNM-71 Quick Start Manual preview
CNM-71
Бренд: Carcomm Страницы: 2
Whispbar K392W Fitting Instructions For Basic Carrier preview
K392W
Бренд: Whispbar Страницы: 14
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Бренд: GMC Страницы: 425
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Бренд: Subaru Страницы: 99
Caltrend BM110 Installation Instructions preview
BM110
Бренд: Caltrend Страницы: 2
Advanced ICE 1296-1 Manual preview
1296-1
Бренд: Advanced ICE Страницы: 4
Icom RMK-5 Instruction Manual preview
RMK-5
Бренд: Icom Страницы: 20
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Бренд: Safe Fleet Страницы: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Бренд: Seat Страницы: 44
Vauxhall Astra 2021 Owner'S Manual preview
Astra 2021
Бренд: Vauxhall Страницы: 259
Xhorse VVDI User Manual preview
VVDI
Бренд: Xhorse Страницы: 48
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Бренд: Car-Systems Страницы: 10
Prorack K577W Fitting Instructions Manual preview
K577W
Бренд: Prorack Страницы: 15
TomTom LINK 105 Installation Manual preview
LINK 105
Бренд: TomTom Страницы: 22
Mazda MX-3 1995 Workshop Manual preview
MX-3 1995
Бренд: Mazda Страницы: 1001

Бренды по названию

Популярные бренды

Загрузить еще бренды